Rancang Bangun Alat Pemberi Makan Ikan Menggunakan Blynk Untuk Keramba Jaring Apung Berbasis IoT
Abstract
Research has been carried out on the Design of Fish Feeding Equipment for IoT-Based Floating Cages. The purpose of this study was to design a fish feeder for floating net cages using ESP-32 CAM, ultrasonic sensor, RTC module and servo motor. The research stages start from hardware design, software design, testing and analysis. The results showed that the RTC Module was functioning properly according to the Blynk Application Time Input Widget. A notification will be sent to the smartphone when the remaining volume of fish feed is less than 20%. ESP32-CAM can send images and stored on webhosting the results of the images displayed are affected by the signal speed. Overall the tool can function well. For further research, you can add a weight sensor to find out how much feed is given in each specified time.
Downloads
References
[2] S. Artisna, I. Umar, and D. Chandra, “Jurnal buana,” Buana, vol. 3, no. 3, pp. 451–465, 2018.
[3] F. Marzuki and S. Ali, “Memberdayakan Ekonomi Ukm Menyelamatkan Danau Maninjau Dari Pencemaran Dan Kerusakan Lingkungan,” J. Ipteks Terap., vol. 12, no. 1, p. 84, 2018, doi: 10.22216/jit.2018.v12i1.2912.
[4] R. Rasidi, E. Erlania, and A. B. Prasetio, “Evaluasi Dan Status Perkembangan Usaha Budidaya Ikan Dalam Keramba Jaring Apung Di Danau Maninjau, Sumatera Barat,” Media Akuakultur, vol. 5, no. 1, p. 51, 2010, doi: 10.15578/ma.5.1.2010.51-56.
[5] V. No and N. Mona, “Konsep Isolasi Dalam Jaringan Sosial Untuk Meminimalisasi Efek Contagious (Kasus Penyebaran Virus Corona Di Indonesia),” J. Sos. Hum. Terap., vol. 2, no. 2, pp. 117–125, 2020, doi: 10.7454/jsht.v2i2.86.
[6] Suharmanto, “Perilaku Masyarakat dalam Pencegahan Penularan COVID-19,” Kedokt. Univ. Lampung, vol. 4 Nomor 2, pp. 91–96, 2020.
[7] M. Yakob, M. T. Hidayat, A. Suciani, and P. Nucifera, “Strategi Pencegahan Penularan Virus Covid-19 Pada Sekolah Dasar Di Kecamatan Pante Bidari Aceh Timur,” Int. J. Community Serv. Learn., vol. 4, no. 3, pp. 209–214, 2020, doi: 10.23887/ijcsl.v4i3.29095.
[8] R. Sistem, “Rancang Bangun Pengukur Suhu Tubuh Menggunakan Multi Sensor,” vol. 1, no. 10, pp. 543–549, 2021.
[9] W. Sari, R. Rasyid, L. Fisika Elektronika, D. Instrumentasi, and J. Fisika, “Rancang Bangun Sistem Termometer Inframerah dan Hand Sanitizer Otomatis untuk Memutus Rantai Penyebaran Covid-19,” J. Fis. Unand, vol. 10, no. 1, pp. 76–82, 2021, [Online]. Available: http://jfu.fmipa.unand.ac.id/76.
[10] A. Andrizal, Y. Yultrisna, J. Junaldi, T. Anggraini, and A. Anton, “Sistem Otomatis Pompa Air dan Sabun pada Wastafel Pencuci Tangan,” Elektron J. Ilm., vol. 12, no. 2, pp. 53–60, 2020, doi: 10.30630/eji.12.2.168.
[11] A. N. Trisetiyanto, “Rancang Bangun Alat Penyemprot Disenfektan Otomatis untuk Mencegah Penyebaran Virus Corona,” J. Informatics Educ., vol. 3, no. 1, pp. 45–51, 2020.
[12] A. M. Putra and A. B. Pulungan, “Alat Pemberian Pakan Ikan Otomatis,” JTEV (Jurnal Tek. Elektro dan Vokasional), vol. 6, no. 2, p. 113, 2020, doi: 10.24036/jtev.v6i2.108580.
[13] A. Departemen et al., “Design of Automatic Fish Feeder Dedy Prijatna 1) , Handarto 1) , Yosua Andreas 2) ,” vol. 12, no. 1, pp. 30–35, 2018.
[14] E. Safrianti, L. O. Sari, and A. Fadilla, “Sistem Otomatisasi Alat Pemberi Pakan Ikan Lele Berbasis Arduino Uno,” Jur. Elektro Fak. Tek. Univ. Riau, pp. 33–37, 2019.
[15] R. Setiawan, “Rancang Bangun Alat Pemberi Pakan Ikan Menggunakan Mikrokontroler,” J. ICTEE, vol. 1, no. 1, pp. 54–64, 2020, doi: 10.33365/jictee.v1i1.698.
[16] A. Hidayat, “Alat Pengatur Takaran Pakan Ikan Otomatis menggunakan metoda fuzzy dengan sensor suhu dan pH,” Elektron J. Ilm., vol. 12, no. 1, pp. 28–33, 2020, doi: 10.30630/eji.12.1.144.
[17] M. Y. Florestiyanto, D. B. Prasetyo, and M. H. R. Handigar, “Pengembangan Alat Pemberi Makan Ikan Otomatis Menggunakan Arduino,” Telematika, vol. 16, no. 2, p. 73, 2019, doi: 10.31315/telematika.v16i2.3185.
[18] S. Sarifudin, M. Manshur, and A. Tirtana, “Penggunaan Komunikasi Bluetooth Pada Smartphone Android Untuk Pengiriman Data Pada Jam Digital Berbasis Arduino,” J. ELTIKOM, vol. 1, no. 2, pp. 102–112, 2018, doi: 10.31961/eltikom.v1i2.22.
[19] R. Roslidar, A. Mufti, and H. Akbarsyah, “Perancangan Robot Light Follower untuk Kursi Otomatis dengan Menggunakan Mikrokontroler ATmega 328P,” J. Rekayasa Elektr., vol. 13, no. 2, p. 103, 2017, doi: 10.17529/jre.v13i2.8093.
[20] H. G. GHIFARI, D. DARLIS, and A. HARTAMAN, “Pendeteksi Golongan Darah Manusia Berbasis Tensorflow menggunakan ESP32-CAM,” ELKOMIKA J. Tek. Energi Elektr. Tek. Telekomun. Tek. Elektron., vol. 9, no. 2, p. 359, 2021, doi: 10.26760/elkomika.v9i2.359.
[21] U. Latifa and J. S. Saputro, “Perancangan Robot Arm Gripper Berbasis Arduino Uno,” Barometer, vol. 3, no. 2, pp. 138–141, 2018.
[22] U. Y. O. Budi Indra Gunawan, “JURNAL RESTI Sistem Pemantau dan Pengendali Suhu Ruang Server Menggunakan Fuzzy,” vol. 4, no. 10, pp. 1–9, 2020._error%3F.
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.